project was undeleted

• Files Changed
• Browse Source

Resolved conflicts
- Update to version 1.0.1
  * linux_spi: Reduce maximum read chunksize
  * Hardcode default spispeed of 2MHz
    Default speed of kernel drivers isn't always sane (any more).
  * Fix dmi_match string for ThinkPad X201
  * verification with sparse layouts
  * Fix erasing of unaligned regions

- Update to version 1.0
  * Support layouts for read and erase commands
  * New command line switch --noverify-all (-N) allows flashing of
    individual regions without reading the whole flash chip
    (particular useful with locked down Intel ME firmware)
  * New command line switch --ifd to read the layout from an
    Intel Firmware Descriptor on flash
  * We got rid of the delay-loop calibration (if the OS provides an
    accurate timer through clock_gettime())
  * Reading speed of USB programmers should have increased (reading
    bigger chunks at once, we reduce the overhead)
  * Support Intel 100 series PCHs (Sunrise Point, coupled with
    Skylake and Kaby Lake) and C620 series PCHs (Lewisburg paired
    with Workstation/Server versions of the former)
  * New programmers
    + Intel 100 series / C620 series PCHs
    + Intel I210 NICs (EEPROM and SPI)
    + AMD Merlin Falcon (FP4)
  * New chips
    + W25Q128.W
- Specfile cleanup
- Verify source signature

• Files Changed
• Browse Source

merge patches in to 0.9.9

- Enable build for ARM

- Update to 0.9.9
  * Enable the dediprog module by default, add support for Dediprog
    SF600 and the new communication protocol of the SF100 with
    newer firmware
  * Add support to update the firmware of Promise UltraATA
    controllers
  * Support new programers: WCH CH341A, VIA VT8251
  * Support new chips:
    + ESI ES25P40, ES25P80, ES25P16
    + GigaDevice GD25VQ41B, GD25Q128C, GD25VQ21B, GD25VQ40C,
      GD25VQ80C and GD25VQ16C, GD25LQ40, GD25LQ80, GD25LQ16,
      GD25LQ64(B), GD25LQ128
    + PMC Pm25LQ020, Pm25LQ040, Pm25LQ080, Pm25LQ016, Pm25LQ032C
    + Sanyo LE25FU406C/LE25U40CMC
    + SST SST25WF020A, SST25WF040B, SST25WF080B
    + Winbond W29C512A/W29EE512
  * Allow to link flashrom statically (with make CONFIG_STATIC=yes)
  * Ease debugging of build problems with libraries
  * Ignore 0x00 as a flash chip manufacturer ID in the generic
    match to avoid ambiguous messages
  * Various improvements for serprog-based programmers
  * Add support for libftdi1
  * Add infrastructure for libusb1 and use it for new programmers
  * Rigorously check integrity of I/O stream data
  * Add make parameters for easier disabling/enabling of various
    classes of programmers

• Files Changed
• Browse Source

Fixed flashrom now that base has updated
- Update to 0.9.8
  * A bunch of newly supported architectures: ARM 64bit, 
    big-endian ARM, PowerPC 64bit, SPARC.
  * Better support for AMD chipsets in general (speed selection, 
    more conservative defaults etc.).
  * Add new programmer support:
  * AMD Yangtze's SPI controller (found in Kabini and Tamesh) as 
    well as the one in Bolton FCHs (A78, A88X, A77E).
  * Intel Silvermont chipsets (Bay Trail, Rangeley and Avoton) and 
    Wildcat Point (for Broadwell).
  * ITE IT8212F parallel programmer as it8212 (found on PCI SATA 
    RAID controllers).
  * VIA VT6421A LPC programmer as atavia (found on PCI SATA 
    controllers).
  * EEPROMs on Intel network cards based on the 82580 NIC 
    (nicintel_eeprom).
  * Intel 82599 10 GbE NICs boot PROMs (part of nicintel_spi).
  * Microchip PICkit 2
  * MSTAR I²C ISP protocol (not compiled in by default). Rewrites the 
    firmware of your screen over VGA/DVI(!).
  * Extension of the rayer_spi module to supported various similar 
    devices (Altera ByteBlasterMV, Atmel STK200/300, Wiggler LPT).
  * Switching betweens chips on boards with GIGABYTE's DualBIOS 
    (using the dualbiosindex programmer parameter).
  * Enable fwh_idsel parameter for C-ICH and ICH2/3/4/5 chipsets.
  * Finer-grained display of support status used for flash chip 
    operations, chipsets, mainboards and programmers (new states: 
    configuration-dependent, not applicable).

• Files Changed
• Browse Source

Update to 0.9.8 release (no r diff)

• Files Changed
• Browse Source

Better buspirate support
--This line, and those below, will be ignored-- Top of tree build with
additional patches for buspirate speed up and better incremental flash

A    0001-Bus-Pirate-UART-speedup.patch
A    0002-add-incremental-flag-to-only-update-regions-specifie.patch
A    diff-0.9.7-r1869.diff
M    flashrom.spec

Diff for working copy: .
Index: flashrom.spec
===================================================================

--- flashrom.spec	(revision cc3c691f9f1e4b378bcee9b735c9ed61)
+++ flashrom.spec	(working copy)
@@ -1,7 +1,7 @@
 #
 # spec file for package flashrom
 #
-# Copyright (c) 2014 SUSE LINUX Products GmbH, Nuernberg, Germany.
+# Copyright (c) 2015 SUSE LINUX Products GmbH, Nuernberg, Germany.
 #
 # All modifications and additions to the file contributed by third parties
 # remain the property of their copyright owners, unless otherwise agreed
@@ -16,15 +16,27 @@
 #
 
 
+%define		baseversion	0.9.7
+%define		incremental	r1869

• Files Changed
• Browse Source

• Browse Source