baserev update by copy to link target

• Files Changed
• Browse Source

- switch to upstream bootstrapped tarball
- add upstream signing key and verify source signature
- drop obsolete texinfo macros

• Files Changed
• Browse Source

baserev update by copy to link target

• Files Changed
• Browse Source

- Update to version 4.5.5 (2023-04-05)
  * Add park to rotorez.c
  * Fix rig power on/off from rigctl cmd line and rigctld
  * Enable async mode by default to prevent WSJT-X crash on IC9700
    with transceive on
  * Fix IC7610 get_powerstat to disable it -- cannot read power status
  * Fix K3 K22 command error for remote operations
  * Fix Gemini DX1200 gemini_set_level
  * Fix async I/O to not call flush
  * Change EX startup commands for Yaesu rigs to allow 
    errors...Win4Yaesu not recognizing EX commands
  * Fix jst145 set_freq and get_freq
  * Restore tcflush as some odd behavior was seen that tclush fixes
  * Fix XG3 operations
  * Separate the validation cmd in newcat.c to allow rig
    post_write_delay to be in effect
  * Increase post_write to 20ms for FT710
  * Add attenuator level control for TS890
  * Update SMeter/SWR tables for TS890
  * Add fix for TMD700
  * Improve FT-857 get_vfo response when error occurs
  * Allow FT-857 to use cached vfo on get_vfo when error
    occurs reading EEPROM
  * Fix FTDX10 FT710 set_level AF
  * Fix FT-450D detection
  * Fix VFO A/B swapping for gpredict -- hopefully better
    behavior for VFO swapping rigs. Should avoid setting RX freq
    while TX and avoid TX freq while RX
  * Fix QRP QDX PTT to new TQ command due to firmware changes
  * Remove EX103 check for FTDX5000
  * Fix K3/K3S VFOB setting of mode/width
  * Fix AGC level display in rigctld
  * Change FTDX10 to no serial handshake
  * Add TS2000 to has_ps exception
  * Add FT991 to 60M exception
  * Fix get_powerstat bad call in rigctl_parse.c
  * Really fix CM108 ptt_bitnum usage
  * Fix Elecraft power2mW precision/accuracy
  * Fix power on/off/on for Icom rigs with rigctld power_on=0

• Files Changed
• Browse Source

baserev update by copy to link target

• Files Changed
• Browse Source

- Update to version 4.5.4 (2023-01-10)
  * Fix CM108 ptt setting for non-default usage
  * Fix power on/off for Icom rigs with rigctld power_on=0
  * Fix get_powerstat status return for non-PS kenwood rigs
  * Fix FT-710, FTDX10, FTDX101D/MP usage on 60M
  * Fix timing on NRD-535D
  * Fix AGC levels with rigctld
  * Fix FTDX3000 EX039 error
  * Fix Elecraft power2mW operation
  * Fix rig_power2mW so it checks all ranges
  * Allow rigctld to start with autopower_on=0 to avoid startup
    timeouts when rig is powered off
  * Fix dummy device to work with grig by disallowing empty "u" call
  * Fix ID5100 and promote to stable and hopefully ID4100 too
  * Remove get_powerstat from Icom ID-5100,ID-4100,ID-31,ID-51 and
    fix get/set freq in all

• Files Changed
• Browse Source

baserev update by copy to link target

• Files Changed
• Browse Source

- Update to version 4.5.3 (2022-12-31)
  * Fix serial.c for hardware flow control on Linux and MacOSy
  * Add QRPLabs QCX/QDX rig -- not quite a TS480
  * Fix QRP QRDX firmware bugs in IF message so PTT works now
  * FTDX5000 will now remember startup front/read settings and restore it
  * Fix FTDX5000 write_delay with microham

• Files Changed
• Browse Source

baserev update by copy to link target

• Files Changed
• Browse Source

- Update to version 4.5.2 (2022-12-23)
  * Fix PowerSDR ability to do commands while powered off
  * Fix TX-500 operations
  * Fix FTDX5000 to return to MIC input on closing
  * Fix rig.c calling rig_get_mode when backend does not have get_mode
  * Fix kenwood_ts890_get_level
  * Add Prosistel D elevation CBOX az to fix problem with azimuth
    control
  * Fix FT736R gpredict usage by adding cached get_freq
  * Fix get_powerstat problem with Log4OM/Flex and others
  * Fix -R option to not need argument
  * Fix -R option to close rig on last rigctld client disconnect
  * Add FTDX1200 to rigs that need to ensure PTT is off before
    changing frequency
  * Add --disable-parallel configure option for mingw builds on Linux

• Files Changed
• Browse Source

baserev update by copy to link target

• Files Changed
• Browse Source

- Update to version 4.5.1 (2022-12-08)
 * FT2000, FTDX3000/D, FT891, FT991, FT950, FTDX5000 now set CAT TOT
   to 100ms
 * Add missing NB2 setting to FT-950, FTDX-1200, FTDX-3000, FTDX-5000,
   FTDX-9000
 * Add missing meter reading to TS-890S -- thanks to Geore Baltz N3GB
 * Fix FT736 VFOB freq and mode set
 * Added send_raw to rigctl -- see rigctl man page
 * Fix AGC Level dumpcaps on most rigs
 * Fix rig_send_raw to return bytes read, fill buffer, and also work
   with fixed length response/null terminator
 * Change all Kenwood rigs to 500ms serial timeout
 * Fix dumpcaps filter printout to only show declared filters
 * Fix triggering PTT on XGComms device on Linux
 * Fix level_gran in all rigs
 * Add RIG_FUNC_TUNER to flrig.c
 * Fix FT-991 level_gran (needs to be done for lots of rigs)
 * Fix man page rigctl to show units for LEVEL items
 * Fix Flex6xxx if_len
 * Fix FLRig set_ptt
 * Fix missing KEYSPD to TS890
 * rigctl 'W' command can now use a singled char terminator like ;
   that allows for variable length responses with no timeout --
   e.g.  WFA; ;
 * New RIG_LEVEL_USB_AF to control audio gain from rig to computer
   -- to allow AGC function in software using RF and USB_AF
 * Add RIG_LEVEL_AGC_TIME to allow AGC/OFF to be set for IC-7300,
   IC-9700, IC-705
 * Add RIG_FUNC_OVF_STATUS to get overflow status for IC-7300,
   IC-9700, IC-705, and IC-R8600

• Files Changed
• Browse Source

baserev update by copy to link target

• Files Changed
• Browse Source

- Update to version 4.5 (2022-10-30)
  * New rotator utility https://www.pianetaradio.it/blog/catrotator/
  * Add FT-710
  * Add Rohde&Schwartz EK89X receiver
  * Add Xeigu X5105
  * Add Gemini DX-1200 HF-1K Amplifiers
  * Kenwood rigs should now support AI command packets
  * Add FT-990UNI for older 990 ROMs 1.2 and earlier
  * Add FT-650
  * Add get_separator and set_separator and -S option for rigctld -- node-red applicability
  * Add GRBLTRK rotor project -- two axis rotor
  * enum meter_level_e is deprecated and will be removed in 4.6
  * Add SDRPlay SDRUno rig -- can now use Data/Pkt in WSJTX
  * Add ability to use cat_string to FLRig via the "w" and "W" commands
  * Add -B/--mapa2b to rigctlcom
    Allows rigctlcom to map set_freq on VFOA to VFOB instead
    This will allow CW Skimmer to work with some rigs (e.g. IC7300) using FM
    mode on VFOA and CW mode on VFOB and split mode transmit on VFOB.
    Clicking on CW Skimmer will change VFOB instead of VFOA to allow
    working dxpeditions where the fox is staying on frequency
  * Add password capability to rigctld via -A switch. 
    rigctld -A will produce a consistent shared key for any
    specific password that can used in \password and rig_set_password
    TBD The shared key can also be placed in .hamlib_settings 
  * Asynchronous rig data output handling to support transceive
    and spectrum data. Mikael, OH3BHX
  * See new set_conf option async for some Icom rigs
  * Multicast UDP packet output for asynchronous data. Mikael, OH3BHX
  * Rig state poll routine to serve commonly used data like frequency
    and mode from cache. Mikael, OH3BHX
  * deprecated hamlib_port_t at front of rig_state structure -- new
    one at end of structure
  * New rig_send_raw to send/read raw command to rig
  * New RIG_LEVEL_BAND_SELECT for Yaesu rigs
  * New rig_get_conf2 to replace rig_get_conf buffer overflow potential
  * New rot_get_conf2 to reaplce rot_get_conf buffer overflow potential
  * Added Barrett 4050 -- not functional yet
  * Added TCI 1.X -- not functional yet
  * Added TM-V71(A)
  * Added IC-F8101
  * Added JRC JST-145 and JST-245
  * Added Xiegu X108G, G90, and X6100
  * Added CODAN Envoy and NGS
  * Added Lab599 TX-500
  * Added GOMSPACE GS100
  * Deprecated: rigctl commands \set_trn (A) and \get_trn (a) as
    they never worked as intended
  * Deprecated: field rig_caps.transceive and RIG_TRN_* macros

• Files Changed
• Browse Source

- Be less strict with required interpreters for tcl and perl
  subpackages (bsc#1195260)
- Drop python2 subpackage as its not relevant to any supported
  openSUSE release

• Files Changed
• Browse Source

- Fixed source URL and duplicate license files

• Files Changed
• Browse Source

- Update to version 4.4
  * Icom rigs now default filter 2 when setting PKTUSB but user can
    override 
  * Fix FTDX9000 meter readings
  * Add Android sensor as a rotator
  * Added rig_get_vfo to some Icom rigs that have XCHG or 0x25
    command capability
  * Added ability to build hamlib with docker
  * Added M0NKA mcHF URP rig
  * Faster serial i/o noticeable on higher baud rates
  * IC7300/9700/7800/785x set_clock/get_clock routines
    added -- no auto set yet
  * Yaesu FT1200/891/991/DX10/DX101/DX101MP set_clock/get_clock
    routines added

• Files Changed
• Browse Source

- Fixed source URL

• Files Changed
• Browse Source

- Update to version 4.3.1
  * Bug fix release
    - Do not do vfo_fixup on satmode rigs
    - Fix compilation of misc.c with gmtime_r replacement function
      for mingw
    - Fix python build.  For some reason casting tp vfo_t in the
      RIG_VFO_N macro broke the swig parsing
    - Append the missing information to build hamlib v4.3 for
      Android NDK
    - Change set_icom_set_mode_with_data to not change mode unless
      necessary
    - Since Icom rigs default to filter 2 if a filter is not
      selected we will do the same when turning on data mode
    - Fix segfault in kenwood_set_vfo
    - scripts: Update example in readme, since 4.0 817 is 1020
    - Make testlibusb.c compatible with libusb < 1.0.23
      Note: On systems with libusb < 1.0.23 a warning will be
      emmitted but compliation should proceed without error.
    - Update testlibusb.c warning to "may be" instead of "will be"
    - Change kenwood to only set VFOA default on 1st rig_open call
- Update to version 4.3
  * libusb-1.0.23 or greater is now required or use --without-libusb
  * Generating documentation now requires GNU source-highlighter.
  * Added IC-575
  * Less VFO swapping of newer Icom rigs -- zero swapping in WSJTX
    and JTDX
  * Dual rotator control in rotctl -R option
  * Started work on simulators -- very crude right now but usable
    to debug some things
  * Overhaul of rig split -- reverse split (VFOA=RX VFOB=TX) should
    work for rigs capable of it
    Starting VFO does not matter -- rig will end up on RX VFO
      S VFOA 1 VFOB
      S VFOB 1 VFOA
      S Main 1 Sub
      S Sub 1 Main
  

• Files Changed
• Browse Source

baserev update by copy to link target

• Files Changed
• Browse Source